The contents of the corrigendum of December 2016 have been included in this copy. measurement methods continue in this standard, but responsibility for influence quantities, performance, and test procedures are transferred to IEC 62586-2. Class A and Class S measurement methods are defined and clarified, while Class B is moved to informative Annex E and considered for future removal underdeviation and overdeviation parameters are moved to informative Annex D the measurement method for conducted emissions in the 2 kHz to 150 kHz range has been added in informative Annex C the measurement method for RVC (rapid voltage change) has been added the measurement method for current, previously informative, is now normative with some changes This edition includes the following significant technical changes with respect to the previous edition: This edition constitutes a technical revision. This third edition cancels and replaces the second edition published in 2008. Depending on the purpose of the measurement, all or a subset of the phenomena on this list may be measured. Emissions in the 2 kHz to 150 kHz range are considered in Annex C (informative), and over- and underdeviations are considered in Annex D (informative). The power quality parameters considered in this standard are power frequency, magnitude of the supply voltage, flicker, supply voltage dips and swells, voltage interruptions, transient voltages, supply voltage unbalance, voltage harmonics and interharmonics, mains signalling on the supply voltage, rapid voltage changes, and current measurements. Measurement of parameters covered by this standard is limited to conducted phenomena in power systems. This standard addresses measurement methods for in-situ measurements. EMC tests are designed to measure electromagnetic emissions and the exposure of electrical and electronic equipment to electromagnetic interference. Measurement methods are described for each relevant parameter in terms that give reliable and repeatable results, regardless of the method's implementation. This can be achieved by measuring the emissions of a. EMC testing guarantees the reliability and interference-free functioning of different electronic devices and systems in a common electromagnetic environment. power supply systems with a declared fundamental frequency of 50 Hz or 60 Hz. Electromagnetic immunity: refers to the ability of a device or system to function correctly in the presence of unwanted emissions. IEC 6:201 5 defines the methods for measurement and interpretation of results for power quality parameters in a.c. Good product design incorporates the application of basic EMC principles such as effective shielding, earthing, and filtering will simultaneously improve electromagnetic immunity and reduce electromagnetic emissions, whilst minimizing risk.IEC 6:2015 is available as IEC 6:2015 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition. The result of this would include product failure during tests and in the real world would mean that the product would be unreliable and not work as intended. If a product has to be redesigned, it can be prohibitively expensive and result in delays to market and a loss in consumer confidence.īad product design (from an EMC or EMI perspective) would be when earthing, filtering, and shielding have not been considered. How to design for EMI & EMC to minimize risk The standards used are therefore based primarily on radiated and conducted tests. The two key methods that electromagnetic activity or ‘energy’ can reach a product are through the air (radiative coupling) or via the cabling (conductive coupling). How will the energy travel from the product to its “victim”?.With what/whom is it going to interfere?.Where is this product going to be used?.The device’s intended application will determine the exact type of testing required. In addition, specific industrial or military standards will apply to the product depending on its target market and therefore also need to be considered.Įvaluating how a device will react when exposed to electromagnetic energy is known as susceptibility or immunity testing and involves determining the ability of a device to tolerate noise from external sources.Meanwhile, emissions testing measures the amount of EMI generated by the device that could affect other electrical products and can provide an accurate measurement of the amount and type of noise generated by a device. However, different requirements in the US and the European Union (EU), as well as differing interpretations of the meanings of EMC and EMI, often cause confusion when it comes to testing. Failing to consider them in the initial stages of product development can result in the time-consuming and costly need to redesign the product at a later stage to meet EMC/EMI specification tests and prevent product failure or safety risk. Electromagnetic compatibility (EMC) and interference (EMI) are both extremely important design considerations.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |